For Sale - PCM - 2129 - 20 to 50 Tons Compact Horizontal Plastic Injection Moulding Machine

We manufacture Compact Horizontal Plastic Injection Moulding Machine in the range of 20 to 50 tons. This machine is available in PE, PM and PI series

Standard Features for PM Series
- 5 Point doubles Toggle clamping system of steel casting
- Mould opening and clamping in three stage
- Manual mould setting gear arrangement
- Automatic lubricating system in Toggle side
- Single stroke hydraulic ejector
- Square tie bar distance with large mould height
- High tensile, hard-chrome plated tie bar
- Electrical interlocks in front and rear safety guards
- Ceramic Band heater
- High torque hydraulic motor for screw drive
- Automatic suck back system
- Two Stage injection speed
- Gas-nitride screw barrel with standard L/D Ratio
- Injection movement is actuated by two hydraulic cylinders, for perfect alignment to the clamp unit
- Injection unit siding on hard-chrome steel treated ground tie bars. Easy access to the screw is ensured
- Stainless steel hopper with magnetic grill with swiveling system to permit the easy change of the material
- Limit switch for stroke control
- MCB Control for each heating zone
- Star Delta starter for pump motor 200 TO 650T
- Overload protection for pump motor
- Standard Features for PE Series

Clamping Bide
- 5 Point doubles Toggle clamping system of steel casting
- Mould opening and clamping in three stage
- Manual mould setting gear arrangement
- Easy and fast lubricating system
- Square tie bar distance with large mould height
- High tensile, hard-chrome plated tie bar
- Electrical interlocks in front and rear safety guards

Injection Side
- Digital temperature controllers and timers
- High torque hydraulic motor for screw drive
- Automatic sucks back system
- Two Stage injection speed
- Gas-nitride screw barrel with standard L/D Ratio
- Injection movement is actuated by Twin hydraulic cylinders, for perfect alignment to the clamp unit
- Injection unit siding on hard-chrome steel treated ground tie bars.
- Stainless steel hopper with magnetic grill with swiveling system.

Hydraulic and Electrical
- Resiliently mounted hydraulic pump
- Suction line oil filer
- Limit switch for stroke control
- MCB Control for each heating zone
- Star Delta starter for pump motor 200 to 650 Tons
- Overload protection for pump motor

Standard Features for PI Series
- 5 Point double Toggle clamping system of steel casting with steel link and steel bushes with tempered steel pins
- Hydraulic ejector through plate with multiple ejector cycles through nine strokes
- Multiple point automatic lubricating system
- Clamp closing and clamp opening profile with programmable and independent strokes and speeds
- Low pressure mould protection with high mould safety
- Freely programmable control of max. 2 core pulls and air for the control of max. 1 valve
- Mould opening and clamping in four stages
- Mould setting gear arrangement by Hydro-motor
- Square tie bar distance with large mould height
- High tensile, hard-chrome platted tie bar
- Electrical interlocks in front and rear safety guards
- Ceramic heater
- High torque hydraulic motor for screw drive
- Automatic sucks back system
- Four stage injection and four stage holding time
- Cold start protection
- Gas-nitride screw barrel with standard L/D Ratio
- Injection movement is actuated by two hydraulic cylinders, for perfect alignment to the clamp unit
- Injection unit sliding on hard-chrome steel treated ground tie bars
- Stainless steel hopper with magnetic grill mounted on a swiveling system
- Injection speed, pressure and holding time profile on 7 steps
- Proportional valve for pressure and flow control with electronic feedback
- Suction and return oil filter
- Component easily accessible for maintenance purpose
- Resiliently mounted hydraulic pump
- Sealed oil tank with oil temperature
- 24 Volt DC solenoid valve
- Clamping and injection strokes are monitor by linear transducers
- M C B Control each heating zone
- Star Delta starter for pump motor 200 TO 650T
- Overload protection for pump motor

For More Details Contact Us:
Payal Industries
Mr. Rajoo Bharadiya
info@payal-india.com
Tel: +91 79 22200746
+91 79 22203787