For Sale - PCM - 949 - Injection Moulding Machine upto 250 tons
Specification
Reference Number
PCM - 949Product
Injection Moulding Machine upto 250 tonsProduct Details
Model:- PAM185T
Injection Unit:
Shot weight [PS]:-540/637 gms.
Swept Volume:-600/708cc
Screw dia:-55 /60Mm
Screw Stroke:-250mm
Screw Speed:-250RPM
Injection Pressure:-1490/1250 Kg/sqcm
Clammping Unit:
Clammping Force:-185Ton
Distance between Tie Bars (HxV):-530x530mm
Minimum Mould Height:- 200mm
Max. daylight:-900mm
Mould Opening Stroke:-700 mm
Hydrulic Ejector Force:-5.7Ton
Hydrulic Ejector stroke:-140mm
Power /Heating Unit :-
Pump Motor:-18.75Kw
Heater Capacity:-10.6Kw
Controller:-
* Self-Adopted PID Temp. Controller
* Mould Memory-30 sets.
* All Input diagnostic display from the screen.
* All output diagnostic display from the screen.
* 16bit high speed Microprocessor.
* Cold start Prevention of Screw.
* Production Counter Facility.
* Self-diagnosis system for fault alarms.
* Graphic for Machine Movement.
* Digital setting of Proportional Pressure & Flow.
Machine:
* Direct Hydrulic Clamping Unit.
* Linear Transducer for clamp and Injection.
* Clamping force can be adjusted up to the maximum figure started to suit the size of the mould.
* Mould safty device gives low-pressure platen approach. Which avoids possible cavity damaged caused by incompletely ejected moulding.
* Speed Movements of the moving platen are adjustable for the complete stroke in both directions of travel and speed of low approach when clamping and opening can be independently varied.
* Large platen area.
* Long rapid platen stroke
* Transducer for Clamp & Injection.
* Injection Pressure applied to material is infinitely variable.
* Screw Speed Infinitely variable by hydraulic control.
* Screw reaction pressure during plasticization is hydraulically adjustable.
* Swiveling Mechanism [Mechanical]
* Suck back in multiple stages.
* Adjustable nozzle Movement in Multiple stages.
* Auto Purge facility.
* Programmable Hydraulic ejector
* Programmable Air Ejector.
* Electrically and Hydrlically Interlocked safety guards.
Injection Unit:
Shot weight [PS]:-540/637 gms.
Swept Volume:-600/708cc
Screw dia:-55 /60Mm
Screw Stroke:-250mm
Screw Speed:-250RPM
Injection Pressure:-1490/1250 Kg/sqcm
Clammping Unit:
Clammping Force:-185Ton
Distance between Tie Bars (HxV):-530x530mm
Minimum Mould Height:- 200mm
Max. daylight:-900mm
Mould Opening Stroke:-700 mm
Hydrulic Ejector Force:-5.7Ton
Hydrulic Ejector stroke:-140mm
Power /Heating Unit :-
Pump Motor:-18.75Kw
Heater Capacity:-10.6Kw
Controller:-
* Self-Adopted PID Temp. Controller
* Mould Memory-30 sets.
* All Input diagnostic display from the screen.
* All output diagnostic display from the screen.
* 16bit high speed Microprocessor.
* Cold start Prevention of Screw.
* Production Counter Facility.
* Self-diagnosis system for fault alarms.
* Graphic for Machine Movement.
* Digital setting of Proportional Pressure & Flow.
Machine:
* Direct Hydrulic Clamping Unit.
* Linear Transducer for clamp and Injection.
* Clamping force can be adjusted up to the maximum figure started to suit the size of the mould.
* Mould safty device gives low-pressure platen approach. Which avoids possible cavity damaged caused by incompletely ejected moulding.
* Speed Movements of the moving platen are adjustable for the complete stroke in both directions of travel and speed of low approach when clamping and opening can be independently varied.
* Large platen area.
* Long rapid platen stroke
* Transducer for Clamp & Injection.
* Injection Pressure applied to material is infinitely variable.
* Screw Speed Infinitely variable by hydraulic control.
* Screw reaction pressure during plasticization is hydraulically adjustable.
* Swiveling Mechanism [Mechanical]
* Suck back in multiple stages.
* Adjustable nozzle Movement in Multiple stages.
* Auto Purge facility.
* Programmable Hydraulic ejector
* Programmable Air Ejector.
* Electrically and Hydrlically Interlocked safety guards.
{{comment.DateTimeStampDisplay}}
{{comment.Comments}}