Required - TTE - 3248 - Melt Pressure Transducers - PT460 Series

Dynisco Range of PT 460 Series:
1) PT460E
- Pressure ranges: 0 - 500 psi to 0 - 30,000 psi
- Output: 3.33 mV/V
- Accuracy: +/- 0.5 percent FSO
- Standard process connection: 1/2-20 UNF
- Standard electrical connection: Bendix PT02A-10-6P

2) PT462E
- Pressure ranges: 0 - 500 psi to 0 - 30,000 psi
- Output: 3.33 mV/V
- Accuracy: +/- 0.5 percent FSO
- Standard process connection: 1/2-20 UNF
- Standard electrical connection: Bendix PT02A-10-6P

3) TPT463E
- Pressure ranges: 0 - 500 psi to 0 - 30,000 psi
- Output: 3.33 mV/V
- Accuracy: +/- 0.5 percent FSO
- Standard process connection: 1/2-20 UNF
- Standard electrical connection: Bendix PT02A-10-6P

Features:
- Accuracy better than +/- 0.5 percent
- Dymax coated stainless steel wetted parts
- Proven sensor design
- 0 - 500 to 0 - 30,000 psi
- Internal 80 percent shunt calibration

Benefits:
- Reliable, repeatable pressure measurements
- Superior abrasion resistance
- Good stability and repeatability
- Wide variety of pressure ranges
- Easy to calibrate with local indicator

The PT460E Series transducer is a +/- 0.5 percent sensor ideal for melt pressure applications requiring simple installation, repeatability and reliability. The PT460E transducers provide the industry standard 3.33 mV/V signal designed to work with most pressure indicators. The PT460E comes equipped with a six pin bendix connector. Optional thermocouple or RTD configurations are available to provide melt temperature. The PT460E features a 1/2-20 UNF thread for installation in standard transducer mounting holes and can be supplied with a variety of other electrical connections if desired.

Specifications:
Performance characteristics:
- Output: 3.33 mV/V +/- 2.0 percent
- Input voltage: 10 Vdc recommended, 12 Vdc maximum
- Combined error: +/- 0.5 percent FSO (Including linearity, repeatability and hysteresis)
- Repeatability: +/- 0.2 percent FSO
- Configuration: Four-arm bonded foil wheatstone bridge strain gage
- Bridge resistance: Input: 345 Ohms minimum
- Output: 350 Ohms +/- 10 percent
- Over pressure: 2 x FSO or 35,000 psi whichever is less
- Zero balance: +/- 10 percent FSO
- Internal shunt calibration (R-Cal): 80 percent FSO +/- 1 percent
- Insulation resistance: 1000 megohms at 50 Vdc

Temperature and mechanical characteristics:
- Max diaphragm temperature: 750 Degree F (400 Degree C)
- Zero shift (due to temperature change): 25 psi/100 Degree F typical (45 psi/100 Degree C)
- Electronics operating temperature: 250 Degree F (121 Degree C)
- Zero shift due to temperature change: +/- 0.05 percent FS/Degree F max (+/- 0.10 percent FS/Degree C max)
- Sensitivity shift due to temperature change: +/- 0.02 percent FS/Degree F max (+/- 0.04 percent FS/Degree C max)
- Mounting torque: 500 inch/lbs. maximum
- Standard wetted parts: Dymax coated 15-5 PH SST

4) PT462E-M10
- Pressure ranges: 0 - 5,000 psi to 0 - 30,000 psi
- Output: 3.33 mV/V
- Accuracy: +/- 1.0 percent FSO
- Standard process connection: M10 x 1
- Standard electrical connection: Bendix PT02A-10-6P

Model PT462E - M10 melt pressure transducer utilizes a small 6mm sensing element for space restricted areas making it the ideal choice for small extruders and rheometers. Model PT462E - M10 incorporates an 18" flexible stem to isolate the electronics housing from the high process temperatures.

Features:
- 6 mm sensing element
- Internal 80 percent shunt calibration
- 0 - 5,000 to 0 - 10,000 psi
- Good stability and repeatability
- Flexible stem

Benefits:
- Fits in space restricted areas, reduces mounting hole dead space
- Easy set - up
- Choice of pressure ranges
- Reliable pressure measurement
- Easy to install and ideal for high local temperatures

Specifications:
Performance characteristics:
- Ranges (psi): 0 - 5,000, 0 - 7,500, 0 - 10,000
- Accuracy: +/- 1.0 percent FSO
- Repeatability: +/- 0.2 percent FSO
- Mounting torque: 500 inch - lbs. maximum
- Maximum pressure: 2 x full range
- Material in contact with pressure media: Inconel 718
- Weight: 1.5 lbs.

Electrical characteristics:
- Configuration: Four active arm bonded Wheatstone bridge strain gage
- Bridge resistance: Input: 345 Ohms minimum; Output: 350 Ohms +/- 10 percent
- Full scale output: 3.33 mV/V +/- 2.0 percent
- Zero balance: +/- 10 percent full scale
- Excitation: 10 Vdc recommended, 12 Vdc maximum
- Internal shunt calibration (R-Cal): 80 percent FSO +/- 1.0 percent
- Insulation resistance: 1,000 megohms at 50 Vdc

Temperature Characteristics
- Transducer diaphragm:
a. Maximum diaphragm temperature: 750 Degree F (400 Degree C)
b. Zero shift due to temperature change: 20 psi/100 Degree F maximum (37 psi/100 Degree C)
- Electronics housing:
a. Maximum temperature: 250 Degree F (121 Degree C)
b. Zero shift due to temperature change: 0.05 percent full scale/Degree F maximum (0.10 percent full scale/Degree C)
c. Sensitivity shift due to temperature change: 0.02 full scale/ Degree F maximum (0.04 percent full scale/Degree C)

5) PT467E
- Pressure ranges: 0 - 500 psi to 0 - 30,000 psi
- Output: 3.33 mV/V
- Accuracy: +/- 0.5 percent FSO
- Standard process connection: 1/2-20 UNF Jam Bushing
- Standard electrical connection: Bendix PT02A-10-6P

Description
Model PT467E is similar to the PT462E yet features a 0.06" diameter exposed capillary. This allows 1/16" radius bends in applications where mounting
space is limited. It also has a free - spinning jam nut that simplifies installation.

Features
- Better than +/- 0.5 percent accuracy
- 3.33 mV/V FSO
- Internal 80 percent shunt calibration
- All stainless steel wetted parts
- 0 - 500 to 0 - 30,000 psi
- Good stability and repeatability
- Exposed, bendable capillary

Benefits
- Reliable pressure measurement
- Standard low level output
- Easy set - up
- Corrosion resistant
- Choice of pressure ranges
- Proven sensor design
- Fits in space restricted areas, ideal for injection molding nozzles

Specifications:
Performance characteristics:
- Ranges (psi): 0 - 500, 0 - 750, 0 - 1,000, 0 - 1,500, 0 - 3,000, 0 - 5,000, 0 - 7,500, 0 - 10,000, 0 - 15,000, 0 - 20,000, 0 - 30,000
- Accuracy: 0.5 percent FSO
- Repeatability: +/- 0.2 percent FSO
- Mounting torque: 500 inch - lbs. maximum
- Maximum pressure: 2 x full range or 35,000 psi (whichever is less)
- Material in contact with pressure media: 15 - 5 PH stainless steel, Dymax coated
- Weight: 1.5 lbs.

Electrical characteristics:
- Configuration: Four active arm bonded wheatstone bridge strain gage
- Bridge resistance: Input: 345 Ohms minimum; Output: 350 Ohms +/- 10 percent
- Full scale output: 3.33 mV/V +/- 2.0 percent
- Zero balance: +/- 10 percent full scale
- Excitation: 10 Vdc recommended, 12 Vdc maximum
- Internal shunt calibration (R-Cal): 80 percent FSO +/- 1.0 percent
- Insulation resistance: 1,000 megohms at 50 Vdc

Temperature characteristics:
- Transducer diaphragm:
a. Maximum diaphragm temperature: 750 Degree F (400 Degree C)
b. Zero shift due to temperature change: 25 psi/100 Degree F maximum (45 psi/100 Degree C)
- Electronics housing:
a. Maximum temperature: 250 Degree F (121 Degree C)
b. Zero shift due to temperature change: 0.05 percent full scale/ Degree F maximum (0.10 percent full scale/ Degree C)
c. Sensitivity shift due to temperature change: 0.02 percent full scale/Degree F maximum
(0.04 percent full scale/Degree C)

6) PT467E-M10
- Pressure ranges: 0 - 5,000 psi to 0 - 10,000 psi
- Output: 3.33 mV/V
- Accuracy: +/- 1.0 percent FSO
- Standard process connection: M10 x 1 Jam Bushing
- Standard electrical connection: Bendix PT02A-10-6P

Description
Model PT467E - M10 features a small, 6 mm sensing element that is ideal for use in space restricted areas or on small extruders or rheometers. Model PT467E - M10 is similar to the model PT462E - M10 yet features a 0.06" diameter exposed capillary to allow 1/16" radius bends in applications where

Features
- 6 mm sensing element
- Exposed, bendable capillary
- Internal 80 percent shunt calibration
- 0 - 5,000 to 0 - 10,000 psi
- Good stability and repeatability
- Flexible stem
- Classic, standard design

Benefits
- Fits in space restricted areas
- Ideal for injection molding nozzles
- Easy set - up
- Choice of pressure ranges
- Proven sensor design
- Easy to install, ideal for high local temperatures
- Economically priced

Specifications:
Performance characteristics:
- Ranges (psi): 0 - 5,000, 0 - 7,500, 0 - 10,000
- Accuracy: +/- 1.0 percent FSO
- Repeatability: +/- 0.2 percent FSO
- Mounting torque: 500 inch - lbs. maximum
- Maximum pressure: 2 x full range
- Material in contact with pressure media: Inconel 718
- Weight: 1.5 lbs.

Electrical characteristics:
- Configuration: Four active arm bonded Wheatstone bridge strain gage
- Bridge resistance: Input: 345 Ohms minimum; Output: 350 Ohms +/- 10 percent
- Full scale output: 3.33 mV/V +/- 2.0 percent
- Zero balance: +/- 10 percent full scale
- Excitation: 10 Vdc recommended, 12 Vdc maximum
- Internal shunt calibration (R-Cal): 80 percent FSO +/- 1.0 percent
- Insulation resistance: 1,000 megohms at 50 Vdc

Temperature Characteristics
- Transducer diaphragm:
a. Maximum diaphragm temperature: 750 Degree F (400 Degree C)
b. Zero shift due to temperature change: 20 psi/100 Degree F maximum (37 psi/100 Degree C)
- Electronics housing:
a. Maximum temperature: 250 Degree F (121 Degree C)
b. Zero shift due to temperature change: 0.05 percent full scale/Degree F maximum (0.10 percent full scale/Degree C)
c. Sensitivity shift due to temperature change: 0.02 percent full scale/ Degree F maximum (0.04 percent full scale/Degree C)

Dynisco's manufactures a wide variety of robust 3.33 mV/V melt pressure transducers, which are designed specifically for harsh and rugged environments of the extrusion and Polymer Processing Industries. Select from one of the many robust and reliable products offered on the market today. No matter what the pressure requirement, whether it is for safety reasons or control to help tighten product specifications, Dynisco can supply it.

(For images, please see next pages)

For More Details Contact:
Manan Enterprise
Mr. Yogesh Desai
Tel.: +91-22-26102833
Mobile: +919819301890
E-mail: manan@bom4.vsnl.net.in